Dutton-Lainson Company

9-1/2 inch offset replacement handle for DL1602A, DL1802A and DLC1800. Ergonomic handle grip.

Similar to 24876, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

2000 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Powder coated copper bronze finish, zinc TUFFPLATE hardware. Handle included.

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3-wire grounded power cord. 4000 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. Similar to SA12000AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

9-1/2 inch offset black plated handle, standard replacement for models DLx1900, DLx1900FC, DLx2300, and DLx2300FC. Can also be used on models DL1602A and DL1802A. Premium cushioned handle grip is softer and more comfortable.

2000 lb 2-speed winch for horizontal pulling applications, with hand brake for manually-controlled load release. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, requiring less effort. Zinc TUFFPLATE finish. Handle included.

Gear and bearing kit for jacks 1250 lb to 2000 lb capacity with 2-1/4 inch outer tube with date code after 4296 (week 42 of 1996)

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3 wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.